Skip to content
Back to the poster maker

Why Do Printers Leave White Borders? Minimum Margins Explained

Print a label sheet, photo, cutting template, sewing pattern, or PDF at an exact size, and the file often fills the page on screen while the printer still leaves a white border.

In most cases Word, Acrobat, or the design application is not adding that border. The printer itself has an area near the edge of the paper where it cannot reliably print. This is commonly called the unprintable area, non-printable area, or hard margin.

Brother's HL-L2460 series, for example, lists a maximum unprintable area of 4.2 mm on each edge for Letter, A4, and Legal paper. That figure is not universal. Different printers, paper sizes, media types, paper paths, duplex settings, and borderless modes can all produce different printable areas.

How Large Are Typical Printer Margins?

For ordinary A4 and Letter printing, many current home and small-office printers have minimum margins of roughly 3–5 mm, with exceptions.

PrinterPaper / modeDocumented minimum or unprintable margin
Brother HL-L2460 seriesA4 / Letter / Legal4.2 mm on all sides
Brother MFC-J4355DW familyCut-sheet paper3 mm on all sides
Epson ET-8550Standard single sheets3 mm minimum
HP OfficeJet Pro 9125eA43.3 mm
HP Smart Tank 7602A43.3 mm
HP Color LaserJet Pro MFP 3301fdwA45 mm
Canon PIXMA TS7720 / TS7700 seriesA45 mm top/bottom, 3.4 mm left/right
Canon PIXMA TS7720 / TS7700 seriesLetter5 mm top/bottom, 6.4/6.3 mm left/right

Rules such as “leave 3 mm around every page” or “5 mm is safe on every printer” are useful approximations, not reliable cross-printer specifications. The printable area depends on this printer, this paper size, media type, feed path, duplex mode, driver, and borderless setting.

Why Paper Size Can Change the Printable Area

A printer's hardware does not necessarily treat A4, Letter, photo paper, envelopes, and specialty media identically.

The Canon TS7700 series is a concrete case: its documented printable area changes between A4 and Letter even though the sheets are fairly similar in size. A4 allows 3.4 mm side margins, while Letter requires roughly 6.3–6.4 mm at the sides.

Paper type can make an even larger difference.

Brother's MFC-J4355DW family uses 3 mm margins on normal cut-sheet paper, but envelopes require 12 mm at the top and bottom. Brother also notes that borderless printing is unavailable for envelopes and when two-sided printing is selected.

Professional and fine-art printing can impose much larger restrictions. Canon's imagePROGRAF PRO-310, for example, lists top and bottom margins of up to 25 mm for some fine-art media.

Is Borderless Printing the Solution?

Sometimes. Borderless printing solves a different problem.

If you are printing a photograph and want ink to reach the physical edge of the sheet, Borderless Printing is usually the right feature. But “borderless” does not necessarily mean that every pixel in the original file appears on the finished sheet. Canon explains that its borderless mode works by enlarging the print data slightly beyond the paper edges. The portion extending beyond the sheet is not printed. Increasing the extension helps eliminate white edges, but it also increases the amount of the image that falls outside the paper. That is why a borderless photograph can look perfect while still losing a small amount of content around its perimeter.

For exact-size work, “fill the paper” and “preserve the document's geometry” pull in opposite directions. Suppose your PDF contains a rectangle exactly 100 mm wide. If your print dialog scales the page to 97%, that rectangle will no longer be 100 mm. A borderless driver that enlarges the page slightly is no different in principle: the output may look better as a photograph, but it is no longer a measurement template. The aim is not to eliminate every white margin. It is to keep the entire intended document inside the printer's printable area without changing its scale.

For photos that must visually fill the sheet: use Borderless Printing and accept a small amount of edge cropping.

For rulers, labels, templates, patterns, plans, or anything dimensionally accurate: avoid borderless expansion and print at 100% / Actual Size.

Why Printer Margins Matter Even More for Tiled Posters

Margins matter more when you use ordinary A4 or Letter paper to make a large tiled poster, sometimes called a block poster. If you are new to this workflow, start with how to print a large image on multiple pages.

A tiled-poster tool divides a large image across many pages. After printing, you trim, align, and assemble those sheets into one poster.

A few millimeters of unexpected clipping on a normal office document may go unnoticed. On a tiled poster, the same problem can repeat across every sheet.

If important image content extends into a printer's unprintable area, you may lose thin strips along tile edges. That makes adjacent sheets harder to align and can produce visible discontinuities in the assembled poster.

For tiled printing, margins therefore serve two useful purposes:

  1. They keep the actual poster image away from uncertain hardware print boundaries.
  2. They provide physical space around each tile that can be handled or trimmed during assembly.

That is why a tiled-poster generator should not assume every printer can safely print within 3 mm of the edge.

Why Rasterbator.io Uses a 10 mm Default Margin

Rasterbator.io's Block Poster Maker uses 10 mm as its default page margin.

That does not mean printers universally have a 10 mm hard margin.

Most ordinary A4 printers in this sample specify substantially less. Modern inkjet printers frequently specify margins around 3–3.3 mm, while several laser printers are closer to 4–5 mm. Representative Letter-mode margins in the sample can reach approximately 6.4 mm.

10 mm is a conservative default. Rasterbator.io cannot assume which printer, driver, paper size, or media configuration a visitor will use. A margin that works on one Epson or HP inkjet may be too small for another laser printer, another paper size, or a different print mode.

Based on the representative A4/Letter models examined for this guide:

  • 3–5 mm covers many common manufacturer-specified hard margins.
  • Around 7 mm is a reasonable minimum safety target if you want to clear even the larger ordinary Letter margins found in this sample.
  • 10 mm adds a practical buffer for differences between printers, drivers, paper feeding, and user configuration.

For a multi-page poster, that extra buffer is usually better than discovering after 20 or 30 sheets that every tile was clipped. 10 mm is a safe starting point, not a technical requirement.

If you know your printer well, have checked its printable-area specification, or have successfully printed a test page, you can reduce the margin and use more of each sheet.

That trade-off is intentional: smaller margins improve paper efficiency; larger margins improve compatibility.

What Margin Should I Use for a Tiled Poster?

For most home printing, these are useful starting points:

Use this when you do not know the exact printable area of the destination printer. It is the safest choice for a generated tiled PDF that may be printed on different A4 or Letter printers.

7 mm — Reasonably conservative

A useful option when maximizing the printable area matters but you still want some protection against printers with larger ordinary hard margins.

5 mm — Printer-dependent

Works with many printers, but not all. Some printers and Letter configurations require more than this.

3 mm — Only when verified

Many modern inkjets support margins around 3 mm, but this should not be treated as a universal setting.

0 mm — Borderless printers only

Use this only if the selected printer, paper size, media type, and driver explicitly support borderless output; remember that borderless modes may enlarge and crop the image.

For an important poster, printing one or two test tiles before the entire PDF is usually worth the paper. When a poster uses dozens of ordinary sheets, a little unused paper is much cheaper than reprinting every tile because each one was clipped.

For trimming, alignment, and joining after printing, see how to assemble a tiled or block poster.

Measure your printer margins

Choose your paper and unit in Block Poster Maker or the full editor, then download the printer margin test under Margins. Print at Actual Size / 100%, with Fit, Shrink, and borderless printing off. Measure the 100 mm or 4 in reference line first.

Find the first complete solid bar on each edge and follow its dotted line to the value. If the short side is under 180 mm or the long side is under 265 mm, the reference runs along the long side and probes appear only on the right and bottom. Measure the top and left with a ruler using the lines marked “check.” If you cannot read a margin, check your printer’s specifications for that paper. Record the largest reading; set Margins to that value plus the overlap and a little extra for paper-feed variation. Probe readings are rounded-up estimates.

A correct reference length does not rule out a shifted print. To check the physical white edge, measure from the paper edge to the nearest end of the solid line marked “check.” Custom-paper tests are in English and require paper at least 125 × 175 mm (about 4.92 × 6.89 in), in either orientation.

How to Print a PDF at the Correct Size in Acrobat

If physical dimensions matter, do not automatically choose Fit.

Adobe Acrobat distinguishes between Actual size, Fit, Shrink oversized pages, and custom scaling. Fit can enlarge small pages or shrink large pages to match the selected paper. Actual Size preserves the document's intended scale.

For a step-by-step explanation, read how to print a PDF at Actual Size.

For a tiled poster PDF generated for A4 or Letter paper:

  1. Select the same physical paper size used when the PDF was generated.
  2. Choose Actual Size or 100%.
  3. Do not select Fit unless you deliberately want the pages rescaled.
  4. Make sure the printer driver has not enabled an additional scaling option.

This is especially important when tile dimensions, alignment marks, rulers, or other physical measurements matter.

Exact-Size Printing on macOS

On macOS, make sure the selected Paper Size matches the actual paper loaded in the printer.

For unusual media, macOS provides Manage Custom Sizes, where you can specify a custom page width and height.

Again, avoid an additional “Scale to Fit” operation when the PDF has already been generated at the required physical page size.

Exact-Size Printing on Linux and CUPS

CUPS exposes options such as media and fit-to-page.

For example, OpenPrinting documents commands that combine media=A4 with fit-to-page. Because fit-to-page deliberately scales the content to the selected medium, it should not be added when you specifically require an existing PDF to remain at 1:1 scale.

Select the correct paper medium and avoid additional page-fitting transformations when dimensional accuracy matters.

DPI Does Not Control Physical Print Scale

Another common source of confusion is DPI.

A printer advertised as 600 dpi, 1200 dpi, or 4800 × 1200 dpi is describing its print-engine resolution. That number does not mean the printer will automatically reproduce an object at the correct physical size.

Physical scale is controlled by the relationship between:

  • the document's page dimensions,
  • the selected paper size,
  • and the print scaling setting.

For example, a photo prepared at 300 PPI for a 4 × 6 inch print would contain roughly 1200 × 1800 pixels.

But if the print dialog scales the page to 95%, its physical dimensions will still change.

When exact dimensions matter, 100% / Actual Size is more important than the headline DPI specification.

What About Labels?

Labels are another situation where shrinking an entire page to avoid clipping is usually the wrong fix.

Imagine that a label sheet is being clipped near the outer edge. Scaling the whole sheet to 95% may move the labels away from the printer's hard margin, but it also changes:

  • label width,
  • label height,
  • spacing between labels,
  • and their position relative to the pre-cut adhesive sheet.

The better approach is to use the manufacturer's exact page template, print at 100%, select the correct paper size, and make sure the template itself does not place required content outside your printer's printable area.

The same principle applies to sewing patterns, cutting guides, architectural plans, rulers, calibration targets, and similar documents.

A Simple Rule for Photos, Templates, and Posters

Photos

Use Borderless Printing when visual edge-to-edge coverage matters more than preserving every outer pixel.

Labels, rulers, templates, and plans

Use the correct paper size and 100% / Actual Size. Accept the printer's physical margins rather than scaling the document.

Tiled posters and block posters

Generate the tiled PDF with a safe page margin (10 mm is a good default when the destination printer is unknown), then print the PDF at 100% / Actual Size.

The poster generator should handle the tiling. The printer driver should not tile or rescale it a second time.

Frequently Asked Questions

What is a normal printer margin?

For many modern consumer inkjet and laser printers, manufacturer-specified margins around 3–5 mm are common on ordinary A4 paper. However, this is not universal. Some paper sizes and configurations require larger margins.

Is 5 mm safe for every printer?

No.

The Canon TS7700 series, for example, specifies approximately 6.4 mm and 6.3 mm side margins on Letter paper, even though its A4 side margins are only 3.4 mm.

Is 10 mm necessary?

Usually not.

It is better understood as a conservative cross-printer default when the exact destination printer is unknown. If you have verified your printer's printable area, you can safely choose a smaller value appropriate for that printer and print mode.

Why does borderless printing crop my photo?

Many borderless systems slightly enlarge the image beyond the physical paper so that small paper-feeding tolerances cannot leave a white line. The portion extending outside the paper is therefore lost. Canon explicitly documents this behavior and allows the amount of extension to be adjusted.

Should I choose Fit or Actual Size when printing a tiled poster?

Normally choose Actual Size / 100%.

A tiled-poster PDF has already been divided into correctly sized physical pages. Applying Fit during printing can rescale every tile and change the final assembled dimensions. Adobe documents Actual Size and Fit as separate page-sizing behaviors.

Can every printer print borderless?

No.

Borderless support depends on the printer, paper size, media type, and print mode. Even printers that support borderless photos may restrict it to certain paper types or sizes. For example, HP specifies borderless support for the OfficeJet Pro 9125e on supported photo media up to Letter/A4.

Sources and further reading

These official manufacturer and platform documents support the examples and print-setting guidance in this article.